Saturday, November 21, 2026

Semroc/Estes Mars Lander Build, Part 3, Landing Gear Housings



These laser cut pieces are close together on the balsa sheet!
The balsa is good, stiff and strong. It should fill and finish up like plastic.

I always remove the ash left after the laser cutting.
Glue on burnt ash doesn't make for a strong bond.

The four "fins" with the notches are the gear struts.  
The inset picture shows the landing gear housing sides, all dight of them.


If there is smoke discoloration from the laser cuts on the cardstock, remove it with a white eraser. A pink pencil end eraser is too rough and can leave a pink tint on the surface.






The sides of the laser cut cardstock also get light sanding with 400 grit on a block. The hold down "tics" should be sanded off so the sides are clean and smooth.


Friday, November 20, 2026

Semroc/Estes Mars Lander Build, Part 2, Fixing The Nose Cone

Before starting the build, I've got to clean up the nose cone.
The shoulder had to be defined. The exposed part of the cone was taped off. 

CWF was brushed onto the shoulder, overlapping the tape edge. 


After the CWF was dry, the tape was pulled leaving a straight line.

This was sanded down until I got a good slip fit in the body tube.
Two wraps of masking tape was wrapped around the tube, even with the top edge. This will keep the wet CWF filler from swelling the tube fibers.
CWF was brushed on overlapping the tape.

When the CWF was about half dried, the nose cone was turned against the tube edge, then lifted to mold and square up the lip.


On the left is the supplied nose cone before filling.

On the right is the filled and reformed cone.

Thursday, November 19, 2026

Semroc/Estes Mars Lander Build, Part 1, Parts




The body tube ends are rough. It'll require light sanding with a block.
Most of the parts are laser cut cardstock.
The balsa is good with a tight grain.





The template and marking guide sheet was a little bent. No big deal, a few passes with an iron will smooth it out.




All the embossed pieces.

If I remember, these aren't as deeply embossed as the old Estes kit. They still add detail.





The nose cone quality wasn't great.
The surface was pitted and there was almost no raised shoulder! 
This will require some some buildup and repair.

Wednesday, November 18, 2026

Semroc/Estes Mars Lander Build, Background

The camping trip was cancelled! Central Florida has three days of rain in the forecast. Nothing worse than a wet muddy dog on a wet, muddy hiking trail.
  
I'll be ending the blog after this build. I know, I stopped the blog once before. This time it's real. 
I figured we'll go out on a high note - 
 
I've built two Mars Lander models before. One Estes original in the early 1970s and more recently a Semroc reissue before I started this blog. 
The earliest I can find a catalog reference is in the 1969 Estes catalog. Only $4.75 cents! I don't think I would try launching it with a recommended B6-2 motor. A C5-3 might be the better choice.

Your shroud skills should be strong to tackle this build. It's a great example of the cardstock details that went into Estes kits in the late 1960s. To see the Estes instructions: CLICK HERE

The description says "spring loaded landing gear". Small, internal rubber bands were used for the landing leg movement. Rubber bands could deteriorate over time. I'll be substituting small springs.

Monday, November 16, 2026

I'm Camping!




No posts until Friday, 
I'm camping with my dog!

I'll be starting a new build - something very special.

Saturday, November 14, 2026

My Work Area - Money Saving TIPS


I don't have a dedicated build area, just the kitchen table. I'm single, so I can get away with this.
I prefer building low power so my work area can be smaller.

Before starting a new build, everything gets cleaned up and organized.
A new #11 style blade goes in my X-Acto handle. For cheap #11 style blades: CLICK HERE 
The old break-off knife tip is snapped off.

The break-off blade knife is for freeing up laser cut fins and general cutting.
The X-Acto knife is for fine shaping and cutting.


Both sanding blocks get new sandpaper. 
Estes and Du-Bro sell great aluminum blocks: CLICK HERE
One block gets 220 grit, the other gets 400 grit.

I buy self-adhesive sandpaper on a roll. It's way cheaper than purchasing the sandpaper cut to size: CLICK HERE

Thursday, November 12, 2026

Estes Strikefighter, Kit #2015, Build, Finished



Whew! This was a challenge.
Thanks go out to SCIGS30. His Rocketry Forum build pics helped with the decal placement. I didn't have a kit face card for reference
The nose cone was beautifully 3D printed by Augendoc.

There are plenty of decals on the upper side of the model.




As with many kits, decals are sparce on the underside.
The original kit had an 18" chute! Probably to keep the overhanging fins from breaking at landing.







The leading and outside fin edge decals were difficult to place. The corner lines should line up, one on top of the other.

Tuesday, November 10, 2026

Estes Strikefighter, Kit #2015, Build, Part 32, Canopy Trim Shrinkage?



I looked at the white canopy trim lines after they were fully dried. I wasn't expecting them to shrink!

It's a minor set back. I'll pull the trim and redo it with a little more length.

Monday, November 9, 2026

Estes Strikefighter, Kit #2015, Build, Part 31, Canopy Frame Trim

The instructions say to paint the "raised areas" of the canopy white. My home made canopy doesn't have a metal frame. I still wanted some white trim.

Instead of trying to paint even, straight lines, I cheat.
Some clear decal paper was spray painted gloss white. You could use white decal paper without the paint but the white won't be as opaque.



Some thin strips were cut.

The verticals were transferred first. 
It's a bit tricky. Make them long enough so the ends will be covered by the next piece.
The second strip goes over the top, covering the first two top ends.

I probably won't add trim to the curves sides. It would be difficult to get the decal strip to curve around the base.

A perfect clone? Nope! Clones ends up close.

Sunday, November 8, 2026

Estes Strikefighter, Kit #2015, Build, Part 30, Canopy Front Decal


Rotate the nose cone to line up the ramjet decal lines with the wing.

The large black decal butts up against the front of the canopy. Note it overlaps the break between the nose cone shoulder and body tube.

I normally would wait for the decal to dry before cutting the joint, but I couldn't get the decal to lay flat. I was concerned it as it dried it might be lifted at the joint.

The decal was cut using a razor blade. It did lay down now. I let it dry before proceeding.


A bit of a white line showed under the cut.

A Sharpie carefully lined the shoulder and body tube edge.

The picture on the right shows no break in the black.

Friday, November 6, 2026

Estes Strikefighter, Kit #2015, Build, Part 29, Attaching The Canopy

The CA glue I use is the "Original" Super Glue. Two little bottles for $1.25 at the Dollar Tree store.

I use a toothpick to apply the glue around the canopy edge.

Set the canopy onto the body, centered over the decal. Tape the canopy down, tight onto the body tube. 



Dip the toothpick tip into a drop of CA glue. Let this first dip of glue dry.

Re-dip the (now sealed) toothpick in the CA drop again.

Set the wet glue toothpick into the canopy/body tube joint and drag the glue drop along the edge. Repeat until the front and rear of the canopy is glued in place.
Remove the tape and glue the sides where the tape blocked the edge.

Thursday, November 5, 2026

Estes Strikefighter, Kit #2015, Build, Part 28, Fin Tip Decals

These fin decals are tricky! Be sure to rub and leave some water down the leading edge and sides of the fin before transferring the decal.

Set the thick black center band down the leading edge of the fin. Hold it up to the light and you can better space the center. 
Be sure the decal corner is at the corner of the fin.
When the center is positioned, roll down the sides.

Cut the top corner close to the black ink. I cut right at the black ink and it didn't run or bleed when soaked.

This is about as good as I could get the two decals to match up!

I counted 31 decals on the sheet!

Wednesday, November 4, 2026

Estes Strikefighter, Kit #2015, Build, Part 27, Decals


There are 30 decals to place!

The front of the canopy decal is set back 1 3/8" from the front of the tube. The instructions say to scrape away paint around the decal for better adhesion of the canopy. You don't have to scrape the paint, I'll show another method coming up.


The center of the ramjet nose cone decal is cut out, close to the black ink. 
The outside of the ring is actually cut closer than shown in the picture.


Set the "NO STEP" wrap decal around the BT-50 tube dry first to get an idea of the spacing. The ends don't touch the root edge.

Tuesday, November 3, 2026

Estes Strikefighter, Kit #2015, Build, Part 26, Decal Fixes

Applying and aligning the wing leading edge decals is tricky!
Trim the clear edge tight at the upper corner.
Set the wide black centerline evenly over the leading edge, then fold down the sides. 

The outside edge (top) decal fits a little over the black outline of the leading edge decal already in place. I didn't get a perfect match at the corner.




Home drawn decals always seem to need some tweaks.
That's why I said to wait before requesting the decal PDF. 

I widened the wide end of the upper decal so the corners would match up (I hope!)
The "DANGER - KEEP OFF" grate decal needed a gray fill.

Another decal printing!

Monday, November 2, 2026

Estes Strikefighter, Kit #2015, Build, Part 25, Canopy Fitting



I was lucky, I got a good canopy on the first try.
Clear, sharp with no bubbles.
The excess was trimmed off and the canopy sanded with 220 grit wrapped around a body tube. First around a BT-50, then around a BT-55.
Initial forming over a smaller tube cuts a sharper arc. Ideally you want to sand in a straight line, up and down. There can be some wiggle. You can get a better fit starting with a smaller diameter tube.



The front and back will sand easily and fit before the sides. Keep sanding until the sides contact the tube. 

Watch for the roll-around "stringers". These can be removed with light passes of 400 grit. Sand only the sides, don't scratch the clear surfaces.







Here's a near fit of the canopy. Note the sides haven't touched the tube yet. That means more sanding.

Sunday, November 1, 2026

Estes Strikefighter, Kit #2015, Build, Part 24, Canopy Carving


On the left - 
The front window line is penciled in. 

On the right - 
That angled taper is cut and sanded.
The top to the rear is rounded.
Side windows are marked.

The front windows are left flat.
The bubble rear canopy is rounded tapering down to the back.

The wooden form is taller than it needs to be. The height will be lower after sanding to fit the BT-55 tube.






For an easier release of the clear vacu-form plastic - 

The entire canopy gets a coat of medium CA glue and is allowed to dry.
This hardens the wood. Sand smooth with 400 grit.